Home » Venting & Flexible Duct » Clothes dryer performance
Clothes dryer performance

Planning points for you dryer venting system

  • When planning a new dryer vent system, always select the route that will provide the straightest and most direct path outdoors.
  • Plan the installation to use the fewest number of elbows and turns.
  • Elbows allow the dryer to sit close to the wall without kinking and/or crushing the transition duct.
  • The male (crimped) end of each section of rigid metal or flexible metal (semi-rigid) ducting must point away from the dryer.
 
  • Rigid metal duct joints should be made air and moisture tight by wrapping the overlapped joints with duct tape or aluminum tape.
  • Duct that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint buildup.
Back to Top

Do's & Don'ts

About ducts...

Do's

  1. To reduce the risk of fire, the dryer MUST BE EXHAUSTED OUTDOORS.
  2. Use only 4" rigid metal or UL-Listed flexible metal (foil-type or semi-rigid) ducting to connect the dryer to the home exhaust system.
  3. For best drying performance, rigid metal transition duct is recommended.
  4. If rigid metal duct cannot be used, UL-Listed flexible metal (semi-rigid) duct should be used.
  5. UL-Listed flexible metal (foil-type) duct should be used only in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used.
  6. Flexible metal (foil-type) duct must be fully extended with excess duct removed to avoid sagging and kinking.
  7. Flexible metal (foil-type or semi-rigid) ducting is acceptable only if they are accessible for cleaning.
  8. Total length of UL-Listed flexible metal (foil-type or semi-rigid) ducting cannot exceed 8’.
 

Don'ts

  1. Never install UL-Listed flexible metal (foil-type or semi-rigid) duct in walls, ceilings, floors or other enclosed spaces.
  2. Do not assemble duct using duct tape, screws or other fastening devices that extend into the interior of the duct. These fasteners can accumulate lint, creating a potential fire hazard.
  3. Do not use duct longer than required. Longer duct systems can accumulate lint, creating a potential fire hazard.
  4. Do not crush, kink or collapse duct.
  5. Avoid resting the duct on sharp objects.

About dryer exhaust…

Do's

  1. Exhaust vent hood must be installed at least 12" from the ground or any object that may be in the path of the exhaust air.
  2. Use caulking compound to seal exterior wall opening around exhaust vent hood.
  3. The exhaust vent hood should cap the vent system to prevent rodents and insects from entering the home.
  4. Before connecting replacement duct to the exhaust outlet of an existing dryer, make sure the exhaust port is clean and the exhaust vent hood is not plugged with lint.
  5. Provide an access to the exhaust system, especially at turns and joints, so system can be inspected and cleaned at least once a year.
  6. Observe all governing codes and ordinances.
 

Don'ts

  1. Do not terminate dryer exhaust in a chimney, a wall, a ceiling, gas vent, crawl space, attic, under an enclosed floor, or in any other concealed space of a building.
  2. Never terminate the dryer exhaust into a common duct with a kitchen exhaust system. A combination of grease and lint creates a potential fire hazard.
Back to Top

 

 

Universal Pest Guard

  • Installs over any style of
    3" or 4" dryer or bathroom
    fan exhaust vent
  • Hinged access guard for
    easy cleaning
 

Louvered Vent Hood
with Plastic Guard

 

Preferred Vent Hood with Removable Guard

Back to Top

Dryer installation applications

 

Back to Top
Clothes dryer safety
Troubleshooting: find solutions to common dryer venting problems
Do's & Don'ts
Clothes dryer performance
Planning points for you dryer venting system
Do's & Don't
Keep birds and rodents out
Dryer installation applications
Downloads
2017 Venting & Flexible Duct Product Catalogue 2017 Venting & Flexible Duct Product Catalogue 2.03 MB
Imperial Group
Head Office & Customer Service
1.800.561.3100
Stay
connected
Home
Company
Opportunities
Contact us
Site Map
Support
Awards & Accolades
In the Community
What's New?
Upcoming Events
Registers & Grilles
Venting & Flexible Duct
Stove
Fireplace
Greentek
Imperial Air Technologies
Railing, Columns & Fencing
Galvanized Duct, Pipe & Fittings
Steel Stud, Channel & Trim
Air Filtration
© 2017 Imperial Manufacturing Group|All rights reserved|A NuFocus Online Solution
Content Support
E-mail Now